Installation of the IDG Oil Filter(s)

TASK 24-21-51-400-041-B
Installation of the IDG Oil Filter(s)

WARNING: WEAR GOGGLES, INSULATED GLOVES AND OTHER PROTECTIVE CLOTHES. HOT OIL CAN BURN YOUR EYES AND SKIN. IF OIL TOUCHES YOUR EYES OR SKIN, GET MEDICAL AID.

CAUTION: DO NOT LET ENGINE OIL FALL ON THE ENGINE. UNWANTED OIL MUST BE REMOVED IMMEDIATELY WITH A CLEAN LINT FREE CLOTH THE OIL CAN CAUSE DAMAGE TO THE SURFACE PROTECTION AND TO SOME PARTS.

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	WARNING NOTICE(S)
No specific	Torque wrench: range to between 15 and 13 lbf.ft (2.03 and 1.76 m.daN )

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.03ABA1)	Synthetic base Lubricating Oil-Turbine Engine - -
(Material No.14QFB1)	Wire-Locking Dia: 0.8 mm CRES Nickel Alloy -

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
FOR [1000EM1] (ENGINE-1)
437AL, 438AR
FOR [1000EM2] (ENGINE-2)
447AL, 448AR

D. Expendable Parts

FIG.ITEM	DESIGNATION	IPC-CSN
3	FILTER ELEMENT	AIPC 24-21-51-02-210
4	O-RING	AIPC 24-21-51-02-215
2	O-RING	AIPC 24-21-51-02-220

E. Referenced Information

REFERENCE	DESIGNATION
TASK 12-13-24-612-041-B	Integrated Drive Generator (IDG) Servicing - Filling of the IDG with Oil or Addition of Oil after a level Check
TASK 71-00-00-710-001-B	Dry Motoring Check
TASK 71-00-00-710-006-B	Minimum Idle Check
TASK 71-13-00-010-040-B	Opening of the Fan Cowl Doors
TASK 71-13-00-410-040-B	Closing of the Fan Cowl Doors
IDG Oil Filters

3. Job Set-up
Subtask 24-21-51-860-055-A ** ON A/C NOT FOR ALL

A. Aircraft Maintenance Configuration
(1) On the center pedestal, on the ENG panel 115VU, make sure that a WARNING NOTICE(S) is in position to tell persons not to start the engine.
(2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure that a WARNING NOTICE(S) is in position to tell persons not to energize the FADEC 1(2).
(3) Make sure that the fan cowl doors are open (Ref. AMM TASK 71-13-00-010-040):
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR

4. Procedure
Subtask 24-21-51-640-060-A ** ON A/C NOT FOR ALL

A. Lubrication of the Consumable Materials
(1) Lubricate the new O-ring (4) with the Synthetic base Lubricating Oil-Turbine Engine - - (Material No.03ABA1) .
(2) Lubricate the new O-ring (2) with the Synthetic base Lubricating Oil-Turbine Engine - - (Material No.03ABA1) .

Subtask 24-21-51-420-077-B ** ON A/C NOT FOR ALL

WARNING: USE PROTECTIVE GOGGLES AND GLOVES WHEN YOU REMOVE OR INSTALL LOCKWIRE. EACH TIME YOU CUT LOCKWIRE, REMOVE AND DISCARD IT IMMEDIATELY. LOOSE LOCKWIRE CAN CUT YOU OR MAKE YOU BLIND, AND/OR CAN CAUSE DAMAGE.

WARNING: MAKE SURE THAT THE COMPONENTS ARE IN THE CORRECT POSITION IN THE FILTER CAVITIES BEFORE YOU INSTALL THE FILTER COVERS. DO NOT TIGHTEN THE FILTER COVER SCREWS TO PUT THE FILTER COMPONENTS IN THE HOUSINGS.

CAUTION: DO NOT CLEAN AND USE AGAIN A FILTER ELEMENT THAT YOU REMOVED.

B. Installation of the Scavenge and Charge Filter Elements

NOTE: The procedure is the same for the two filters

(1) Remove the blanking cap from the filter cavity port.
(2) Install the AIPC 24-21-51-02-215 O-RING (4) on the filter element (3) and make sure that it is in the correct position.
(3) Install the new AIPC 24-21-51-02-220 O-RING (2) on the filter cover (1) and make sure that it is in the correct position.
(4) Put the AIPC 24-21-51-02-210 FILTER ELEMENT (3) in the filter cavity.
(5) Install the filter cover (1).
(6) TORQUE the filter cover to between 15 and 13 lbf.ft (2.03 and 1.76 m.daN )

.
(7) Safety the filter cover with 14QFB1Wire-Locking Dia: 0.8 mm CRES Nickel Alloy -.

Subtask 24-21-51-612-055-A ** ON A/C NOT FOR ALL

C. Fill the IDG oil system (Ref. AMM TASK 12-13-24-612-041).

Subtask 24-21-51-210-062-A ** ON A/C NOT FOR ALL

D. Visual Inspection for Oil Leaks
(1) Do dry motoring (Ref. AMM TASK 71-00-00-710-001) and make sure that there are no oil leaks at the cover(s)of the IDG oil filter(s).

NOTE: We recommend that you do the visual inspection again to make sure that there are no oil leaks at the cover of the IDG oil filter. Do this inspection at the next time you operate the engine at a minimum idle (Ref. AMM TASK 71-00-00-710-006).

When you operate the engine at minimum idle, the oil pressure in the lubrication system and the cooling system of the IDG is higher and the oil circulation time is longer.

5. Close-up
Subtask 24-21-51-410-057-A ** ON A/C NOT FOR ALL

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the fan cowl doors (Ref. AMM TASK 71-13-00-410-040):
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR
(3) Remove the WARNING NOTICE(S).

[Rev.10 from 2021] 2026.03.31 23:21:24 UTC