Removal of the IDG Oil Charge and Scavenge Filter-Elements

TASK 24-21-51-000-804-A
Removal of the IDG Oil Charge and Scavenge Filter-Elements

WARNING: BE CAREFUL WHEN YOU DO WORK ON THE ENGINE AFTER SHUTDOWN. THE ENGINE CAN STAY HOT FOR A LONG TIME. IF YOU DO NOT OBEY THIS INSTRUCTION, INJURY CAN OCCUR.

WARNING: WEAR GOGGLES, INSULATED GLOVES AND OTHER PROTECTIVE CLOTHES. HOT OIL CAN BURN YOUR EYES AND SKIN. IF OIL TOUCHES YOUR EYES OR SKIN, GET MEDICAL AID.

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

CAUTION: DO NOT LET ENGINE OIL FALL ON THE ENGINE. UNWANTED OIL MUST BE REMOVED IMMEDIATELY. THE OIL CAN CAUSE DAMAGE TO THE SURFACE PROTECTION AND TO SOME PARTS.

ZONE: 453
ZONE: 463
FIN: 4000XU1 ** ON A/C NOT FOR ALL
FIN: 4000XU2 ** ON A/C NOT FOR ALL

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 1M(3 FT)
No specific	1	CONTAINER 20L (5 USGAL)
No specific	AR	COVER - PROTECTION

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
453	HOT SECTION
463	HOT SECTION
FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
437AL, 438AR, 451AL, 452AR
FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
447AL, 448AR, 461AL, 462AR

C. Referenced Information

REFERENCE	DESIGNATION
TASK 12-13-24-680-802-A	Draining of the Oil from the Integrated Drive Generator (IDG)
TASK 24-21-00-210-807-A	Inspection of the IDG Oil Charge and Scavenge Filter Elements
TASK 71-00-00-860-833-A	Procedure to Prevent Engine Motoring
TASK 71-13-00-010-802-A	Opening of the Fan Cowl Doors
TASK 78-30-00-040-805-A	Deactivation of the Thrust Reverser System for Ground Maintenance
TASK 78-36-00-010-802-A	Opening of the Thrust Reverser Cowl-Doors
IDG Oil Filter Elements

3. Job Set-up
Subtask 24-21-51-941-063-A ** ON A/C NOT FOR ALL

A. Safety Precautions
(1) Do the procedure to prevent engine motoring
(Ref. AMM TASK 71-00-00-860-833).

Subtask 24-21-51-010-082-A ** ON A/C NOT FOR ALL

B. Get Access
(1) Open the fan cowl doors (Ref. AMM TASK 71-13-00-010-802):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
437AL 438AR
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
447AL 448AR

Subtask 24-21-51-040-050-A ** ON A/C NOT FOR ALL

C. Deactivation of the Thrust Reverser System for Ground Maintenance

WARNING: YOU MUST DEACTIVATE THE THRUST REVERSER BEFORE YOU DO WORK ON OR AROUND IT. IF YOU DO NOT, THE THRUST REVERSER CAN OPERATE ACCIDENTALLY AND CAUSE AN INJURY AND/OR DAMAGE.

(1) Do the deactivation of the thrust reverser system for ground maintenance (Ref. AMM TASK 78-30-00-040-805).

Subtask 24-21-51-010-085-A ** ON A/C NOT FOR ALL

D. Get Access
(1) Open the thrust-reverser cowl-doors (Ref. AMM TASK 78-36-00-010-802):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
451AL 452AR
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
461AL 462AR
(2) Put an ACCESS PLATFORM 1M(3 FT) in position.
(3) Installation of the engine protection covers

CAUTION: INSTALL PROTECTION COVERS ON ALL THE OPENINGS IMMEDIATELY TO PREVENT DAMAGE TO THE ENGINE.

(a) Install all the necessary COVER - PROTECTION to prevent damage to the engine.

4. Procedure

CAUTION: WIPE CLEAN ALL PARTS AND TOOLS AS NECESSARY TO REMOVE UNWANTED DEBRIS AND PREVENT DAMAGE TO THE ENGINE.

Subtask 24-21-51-680-059-A ** ON A/C NOT FOR ALL

A. Draining of the Oil from the IDG
(1) Locate the IDG on the left rear side of the main gearbox.
(2) Find the IDG filter elements under the IDG.
(3) Drain the oil from the IDG (Ref. AMM TASK 12-13-24-680-802).

Subtask 24-21-51-020-112-A ** ON A/C NOT FOR ALL

B. Removal of the IDG Oil Charge and Scavenge Filter Elements
(1) Make sure that the CONTAINER 20L (5 USGAL) in position below the IDG.
(2) Cut and remove the lockwire from the two caps (3).

WARNING: USE PROTECTIVE GOGGLES AND GLOVES WHEN YOU REMOVE OR INSTALL LOCKWIRE. EACH TIME YOU CUT LOCKWIRE, REMOVE AND DISCARD IT IMMEDIATELY. LOOSE LOCKWIRE CAN CUT YOU OR MAKE YOU BLIND, AND/OR CAN CAUSE DAMAGE.

(a) Cut and remove the lockwire from the two caps (3).
(3) Remove the two caps (3).
(4) Remove the two filter elements (2).
(5) Put a label to identify the IDG oil charge and scavenge filter elements (2).
(6) Do an inspection for contamination of the two filter elements (Ref. AMM TASK 24-21-00-210-807).
(7) Remove and discard the packings (1) and (4).
(8) Discard the two filter elements (2).

[Rev.10 from 2021] 2026.03.31 23:21:31 UTC