DOC AIRBUS | AMM A320FInstallation of the Programming and Test Panel
TASK 23-73-18-400-001-A
Installation of the Programming and Test Panel
Self Explanatory
2. Job Set-up Information
A. Referenced Information
3. Job Set-up
Subtask 23-73-18-861-051-A ** ON A/C NOT FOR ALL Subtask 23-73-18-865-051-A ** ON A/C NOT FOR ALL
Subtask 23-73-18-420-050-A ** ON A/C NOT FOR ALL
Subtask 23-73-18-862-050-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.03.31 23:17:56 UTC
Installation of the Programming and Test Panel
FIN: 110RH ** ON A/C NOT FOR ALL
1. Reason for the JobSelf Explanatory
2. Job Set-up Information
A. Referenced Information
| REFERENCE | DESIGNATION |
|---|---|
| TASK 23-73-00-740-005-A | BITE-Test of the Cabin Intercommunication Data System (CIDS) through the CFDS |
| TASK 23-73-19-400-001-A | Installation of the Cabin Assignment Module |
| TASK 24-41-00-861-002-A | Energize the Aircraft Electrical Circuits from the External Power |
| TASK 24-41-00-861-002-A-01 | Energize the Aircraft Electrical Circuits from the APU |
| TASK 24-41-00-861-002-A-02 | Energize the Aircraft Electrical Circuits from Engine 1(2) |
| TASK 24-41-00-862-002-A | De-energize the Aircraft Electrical Circuits Supplied from the External Power |
| TASK 24-41-00-862-002-A-01 | De-energize the Aircraft Electrical Circuits Supplied from the APU |
| TASK 24-41-00-862-002-A-02 | De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2) |
Programming and Test PanelSubtask 23-73-18-861-051-A ** ON A/C NOT FOR ALL Subtask 23-73-18-865-051-A ** ON A/C NOT FOR ALL
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:
4. Procedure| PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 121VU | COM NAV/CIDS/PROG &/TST PNL | 161RH | M07 |
| ** ON A/C NOT FOR ALL | |||
| 121VU | COM NAV/CIDS/PROG &/TST PNL | 161RH | M08 |
Subtask 23-73-18-420-050-A ** ON A/C NOT FOR ALL
A. Installation of the Programming and Test Panel (PTP)
(1) Clean the component interfaces and the adjacent area.
(2) Do an inspection of the component interfaces and the adjacent area.
(3) Install the Cabin Assignment Module (CAM).
(Ref. AMM TASK 23-73-19-400-001)
(4) Install the brackets (2) to the PTP (1) with the screws (3) and the washers (4).
(5) Remove the CAP-BLANKING from each electrical connector and receptacle.
(6) Connect the electrical connector (11) to the PTP (1).
(7) Install the PTP (1) with the screws (5) and the washers (6).
(8) Install the cover (9) with the screws (7) and the washers (8).
(9) Close the access door (10).
(10) Make sure that the work area is clean and clear of tools and other items.
Subtask 23-73-18-865-052-A ** ON A/C NOT FOR ALL (1) Clean the component interfaces and the adjacent area.
(2) Do an inspection of the component interfaces and the adjacent area.
(3) Install the Cabin Assignment Module (CAM).
(Ref. AMM TASK 23-73-19-400-001)
(4) Install the brackets (2) to the PTP (1) with the screws (3) and the washers (4).
(5) Remove the CAP-BLANKING from each electrical connector and receptacle.
(6) Connect the electrical connector (11) to the PTP (1).
(7) Install the PTP (1) with the screws (5) and the washers (6).
(8) Install the cover (9) with the screws (7) and the washers (8).
(9) Close the access door (10).
(10) Make sure that the work area is clean and clear of tools and other items.
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
Subtask 23-73-18-740-050-A ** ON A/C NOT FOR ALL | PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 121VU | COM NAV/CIDS/PROG &/TST PNL | 161RH | M07 |
| ** ON A/C NOT FOR ALL | |||
| 121VU | COM NAV/CIDS/PROG &/TST PNL | 161RH | M08 |
C. Do the BITE-test of the Cabin Intercommunication Data System (CIDS).
(Ref. AMM TASK 23-73-00-740-005)
5. Close-up(Ref. AMM TASK 23-73-00-740-005)
Subtask 23-73-18-862-050-A ** ON A/C NOT FOR ALL