Removal of the Static Discharger Retainer

TASK 23-61-42-000-001-A
Removal of the Static Discharger Retainer

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND THE RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING GEAR. THIS WILL PREVENT UNWANTED MOVEMENT OF THE LANDING GEAR, AND THUS POSSIBLE INJURY TO PERSONS AND DAMAGE TO THE AIRCRAFT AND/OR EQUIPMENT.

WARNING: BEFORE YOU START WORK, YOU MUST PUT ON A SAFETY HARNESS AND ATTACH IT TO THE ACCESS PLATFORM. WITHOUT A SAFETY HARNESS, YOU CAN FALL. THIS CAN KILL YOU OR CAUSE YOU INJURY.

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

ZONE: 324
ZONE: 326
ZONE: 330
ZONE: 340
ZONE: 530
ZONE: 590
ZONE: 630
ZONE: 690

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 12M (40 FT) - ADJUSTABLE
No specific	AR	SAFETY BARRIER(S)
No specific	AR	SAFETY CLIP - CIRCUIT BREAKER
No specific	6	SCRAPER - NON METALLIC
No specific	AR	WARNING NOTICE(S)

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
324	VERTICAL STABILIZER TIP
326	RUDDER
330	THS LH AND LH ELEVATOR
340	THS RH AND RH ELEVATOR
530	L WG FLAP TAB, FLAP TRACK FAIR & WG TIP
590	AILERON
630	RIGHT WING FLAP TRACK FAIR AND WING TIP
690	AILERON

C. Referenced Information

REFERENCE	DESIGNATION
TASK 23-61-41-000-001-A	Removal of the Static Discharger
TASK 55-44-11-000-001-A	Removal of the Rudder Tip
TASK 57-55-11-000-001-A	Removal of the Flap Track Fairings Nos. 2, 3 and 4
TASK 57-55-11-000-004-A	Removal of the Flap Track Fairings Nos. 2, 3 and 4
SRM 514211
Static Discharger Retainers - Vertical Stabilizer Tip, Rudder and THS
Static Discharger Retainers - Engine Pylon and Flap Track Fairings ** ON A/C NOT FOR ALL
Static Discharger Retainers - Flap Track Fairings ** ON A/C NOT FOR ALL
Static Discharger Retainers - Ailerons ** ON A/C NOT FOR ALL
Static Discharger Retainers - Ailerons ** ON A/C NOT FOR ALL
Static Discharger Retainers - Wing Tips ** ON A/C NOT FOR ALL
Static Discharger Retainers - Wing Tip Fences ** ON A/C NOT FOR ALL
Static Discharger Retainers - Wing Tip Fences ** ON A/C NOT FOR ALL
Static Discharger Retainers - Sharklets ** ON A/C NOT FOR ALL

3. Job Set-up
Subtask 23-61-42-941-050-A

A. Safety Precautions
(1) As necessary, use the applicable SAFETY BARRIERS, specified by the operator's instructions and your local regulations.
(2) In the cockpit, put the WARNING NOTICE(S) in position to tell persons not to operate the flight controls.

Subtask 23-61-42-865-050-A

B. Open, safety and tag this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/ELAC1/NORM/SPLY	15CE1	B11
49VU	FLIGHT CONTROLS/THS/ACTR/MOT2	19CE2	B09
49VU	FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1	6CV	B07
49VU	AUTO FLT/FAC1/28VDC	5CC1	B04
49VU	AUTO FLT/FAC1/26VAC	14CC1	B03
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/ELAC1/NORM/SPLY	15CE1	B06
49VU	FLIGHT CONTROLS/THS/ACTR/MOT2	19CE2	B04
49VU	FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1	6CV	B02
49VU	AUTO FLT/FAC1/28VDC	5CC1	H10
49VU	AUTO FLT/FAC1/26VAC	14CC1	H09
** ON A/C ALL
105VU	FLIGHT CONTROLS/ELAC2/STBY SPLY	16CE2	A02
105VU	FLT CTL/ELAC1/STBY SPLY	16CE1	A01
121VU	AUTO FLT/FAC2/28VDC	5CC2	M19
121VU	AUTO FLT/FAC2/26VAC	14CC2	M18
121VU	FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2	8CV	Q21
121VU	FLIGHT CONTROLS/THS ACTR/MOT3	19CE3	Q17
121VU	FLIGHT CONTROLS/THS ACTR/MOT1	19CE1	Q16
121VU	FLIGHT CONTROLS/ELAC2/NORM/SPLY	15CE2	R20

Subtask 23-61-42-010-050-A

C. Get Access
(1) Put the ACCESS PLATFORM 12M (40 FT) - ADJUSTABLE below the applicable static discharger.
(2) Remove the applicable static discharger (Ref. AMM TASK 23-61-41-000-001).

4. Procedure
Subtask 23-61-42-020-051-A

A. Removal of the Static Discharger Retainers from Zones 324 (Vertical Stabilizer Tip), 326 (Rudder) and 330 (340) (Trimmable Horizontal Stabilizer (THS))

Static Discharger Retainers - Vertical Stabilizer Tip, Rudder and THS

(1) Remove the sealant with the SCRAPER - NON METALLIC from the rivets, static discharger retainers and supports, as applicable:
(a) For the static discharger retainers installed on the vertical stabilizer:
1 On the vertical stabilizer tip, remove the sealant from:

The rivets (4)
Around the retainer (3).

2 On the rudder, remove the sealant from:

The rivets (2) and (4)
Around the retainers (1) and (3).

(b) For the static discharger retainers installed on the THS:
1 On the elevator, remove the sealant from:

The rivets (11), (12), (14), (16) and (17)
Around the retainers (10), (13) and (15) and the adapter (9).

2 On the THS tip, remove the sealant from:

The rivets (6) and (8)
Around the retainer (7) and the adapter (5).

(2) For the applicable static discharger retainer(s), remove the rivets SRM 514211.

CAUTION: WHEN YOU REMOVE THE RIVETS, BE CAREFUL NOT TO CAUSE THE RIVET HOLES TO BECOME TOO LARGE. IF YOU DO NOT OBEY THIS PRECAUTION, IT WILL BE NECESSARY TO DO A REPAIR OF THE APPLICABLE ZONE BEFORE YOU INSTALL NEW RIVETS.

(a) For the static discharger retainers installed on the vertical stabilizer:
1 Remove the rivets (4) from the vertical stabilizer tip.
2 Remove the rivets (2) from the rudder trailing edge.
3 Remove the rudder tip (Ref. AMM TASK 55-44-11-000-001).
4 Remove the rivets (4) from the rudder tip.
(b) For the static discharger retainers installed on the THS:
1 Remove the rivets (11), (12), (14), (16) and (17) from the elevator.
2 Remove the rivets (6) and (8) from the THS tip.
(3) Remove the static discharger retainers and supports as applicable:
(a) For the static discharger retainers installed on the vertical stabilizer:
1 Remove the retainer (3) from the vertical stabilizer tip.
2 Remove the retainer (1) from the rudder trailing edge.
3 Remove the retainer (3) from the rudder tip.
(b) For the static discharger retainers installed on the THS:
1 Remove the retainer (15) and the shim (18) from the trailing edge of the elevator.
2 Remove the retainer (13) from the trailing edge of the elevator.
3 Remove the retainer (10) and the adapter (9) from the elevator tip.
4 Remove the retainer (7) and the adapter (5) from the THS tip.

Subtask 23-61-42-020-052-C ** ON A/C NOT FOR ALL

B. Removal of the Static Discharger Retainers from Zones 470 (480) (Engine Pylon), 531 (631), 532 (632) and 533 (633) (Flap Track Fairings)

Static Discharger Retainers - Engine Pylon and Flap Track Fairings ** ON A/C NOT FOR ALL

(1) Remove the sealant with the SCRAPER - NON METALLIC from the rivets and the static discharger retainers as applicable:
(a) For the static discharger retainers installed on the flap-track fairing 2, flap-track fairing 3 and flap-track fairing 4:
1 Remove the sealant from:

The rivets (2) and (3)
Around the retainer (4).

(b) For the static discharger retainers installed on the engine pylon:
1 Remove the sealant from:

The rivets (11)
Around the retainer (10).

(2) For the applicable static discharger retainer(s), remove the rivets SRM 514211.

(a) For the static discharger retainers installed on flap-track fairing 2, flap-track fairing 3 and flap-track fairing 4:
1 Remove the top cover (1) from the flap track fairing (Ref. AMM TASK 57-55-11-000-001) or (Ref. AMM TASK 57-55-11-000-004).
2 Remove the nut (5), washer (6), bolt (8) and disconnect the bonding lead (7) from the plate (9).
3 Remove the rivets (2) and (3) from the flap track fairing.
(b) For the static discharger retainer installed on the engine pylon, remove the rivets (11).
(3) Remove the static discharger retainers and supports as applicable:
(a) For the static discharger retainers installed on flap-track fairing 2, flap-track fairing 3 and flap-track fairing 4:
1 Remove the retainer (4).
2 Remove the plate (9).
(b) For the static discharger retainer on the engine pylon, remove the retainer (10).

Subtask 23-61-42-020-052-D ** ON A/C NOT FOR ALL

B. Removal of the Static Discharger Retainers from Zones 531 (631), 532 (632) and 533 (633) (Flap Track Fairings)

Static Discharger Retainers - Flap Track Fairings ** ON A/C NOT FOR ALL

(1) Remove the sealant with the SCRAPER - NON METALLIC from the rivets and the static discharger retainers as applicable:
(a) For the static discharger retainers installed on flap-track fairing 2, flap-track fairing 3 and flap track fairing 4:
1 Remove the sealant from:

The rivets (2) and (3)
Around the retainer (4).

(2) For the applicable static discharger retainer(s), remove the rivets SRM 514211.

(a) For the static discharger retainers installed on flap-track fairing 2, flap-track fairing 3 and flap-track fairing 4:
1 Remove the top cover (1) from the flap track fairing (Ref. AMM TASK 57-55-11-000-001) or (Ref. AMM TASK 57-55-11-000-004).
2 Remove the nut (5), washer (6), bolt (8) and disconnect the bonding lead (7) from the plate (9).
3 Remove the rivets (2) and (3) from the flap track fairing.
(3) Remove the static discharger retainers and supports as applicable:
(a) For the static discharger retainers installed on flap-track fairing 2, flap-track fairing 3 and flap-track fairing 4:
1 Remove the retainer (4).
2 Remove the plate (9).

Subtask 23-61-42-020-053-A ** ON A/C NOT FOR ALL

C. Removal of the Static Discharger Retainers from Zone 590 (690) (Ailerons)

Static Discharger Retainers - Ailerons ** ON A/C NOT FOR ALL

(1) Remove the sealant with the SCRAPER - NON METALLIC from:

The rivets (7), (8), (11) and (12)
Around the retainers (10) and (14).

(2) For the applicable static discharger retainer(s), remove the rivets SRM 514211.

(a) Remove the rivets (7), (8), (11) and (12).
(3) Remove the retainer (10), then remove and discard washer (9).
(4) Remove the retainer (14), then remove and discard washers (13).

Subtask 23-61-42-020-053-B ** ON A/C NOT FOR ALL

C. Removal of the Static Discharger Retainers from Zone 590 (690) (Ailerons)

Static Discharger Retainers - Ailerons ** ON A/C NOT FOR ALL

(1) Remove the sealant with the SCRAPER - NON METALLIC from:

The rivets (1) and (3)
Around the retainer (2).

(2) For the applicable static discharger retainer(s), remove the rivets SRM 514211.

(a) Remove the rivets (1) and (3).
(3) Remove the retainer (2) from the aileron.

Subtask 23-61-42-020-054-D ** ON A/C NOT FOR ALL

D. Removal of the Static Discharger Retainers from Zone 534 (634) (Wing-Tip)

Static Discharger Retainers - Wing Tips ** ON A/C NOT FOR ALL

(1) Remove the sealant with the SCRAPER - NON METALLIC from:

The rivets (1) and (3)
Around the retainer (2).

(2) For the applicable static discharger retainer(s), remove the rivets SRM 514211.

(a) Remove the rivets (1) and (3).
(3) Remove the retainer (2).

Subtask 23-61-42-020-055-D ** ON A/C NOT FOR ALL

E. Removal of the Static Discharger Retainers from Zone 534 (634) (Wing-Tip Fence)

Static Discharger Retainers - Wing Tip Fences ** ON A/C NOT FOR ALL

(1) If necessary, remove the sealant with the SCRAPER - NON METALLIC from:

The rivets (1), (2), (6) and (8)
Around the retainers (3), (5) and (9), and the packers (4) and (7).

(2) For the applicable static discharger retainer(s), remove the rivets SRM 514211.

(a) Remove the rivets (1), (2), (6) and (8).
(3) Remove the retainers (3), (5) and (9), and the packers (4) and (7).

Subtask 23-61-42-020-055-E ** ON A/C NOT FOR ALL

E. Removal of the Static Discharger Retainers from Zone 534 (634) (Wing-Tip Fence)

Static Discharger Retainers - Wing Tip Fences ** ON A/C NOT FOR ALL

(1) If necessary, remove the sealant with the SCRAPER - NON METALLIC from:

The rivets (1), (4) and (6)
Around the retainers (2), (5) and (7), and the packer (3).

(2) For the applicable static discharger retainer(s), remove the rivets SRM 514211.

(a) Remove the rivets (1), (4) and (6).
(3) Remove the retainers (2), (5) and (7), and the packer (3).

Subtask 23-61-42-020-056-A ** ON A/C NOT FOR ALL

F. Removal of the Static Discharger Retainers from Zone 534 (634) (Sharklet)

Static Discharger Retainers - Sharklets ** ON A/C NOT FOR ALL

(1) If necessary, remove the sealant with the SCRAPER - NON METALLIC from the rivets and around the static discharger retainers.
(2) For the applicable static discharger retainer(s), remove the rivets SRM 514211.

(a) Remove the rivets (1) from the retainer (2).
(b) Remove the rivets (3), (4), (5) and (6) from the retainer (7).
(c) Remove the rivets (8), (9) and (10) from the retainer (11).
(d) Remove the rivets (12), (13), (14), (15) and (16) from the retainer (17).
(e) Remove the rivets (18), (19), (20) and (21) from the retainer (22).
(3) Remove the retainers (2), (7), (11), (17) and (22).

[Rev.10 from 2021] 2026.04.02 06:12:17 UTC