Removal of the Maintenance-Interphone Jack Harness

TASK 23-44-41-000-803-A
Removal of the Maintenance-Interphone Jack Harness

WARNING: WEAR APPLICABLE PERSONAL PROTECTIVE EQUIPMENT (PPE) WHEN YOU DO THIS TASK. BEFORE YOU USE PPE, READ, UNDERSTAND AND OBEY ALL INSTRUCTIONS FOR ITS USE. THESE INSTRUCTIONS INCLUDE INSTRUCTIONS FROM THE MANUFACTURER, YOUR EMPLOYER AND GOVERNMENT REGULATIONS. YOU CAN GET INJURED IF YOU DO NOT USE PPE. GET INSTRUCTIONS FROM YOUR EMPLOYER ON WHICH PPE IS NECESSARY.

WARNING: BE CAREFUL WHEN YOU DO WORK ON THE ENGINE AFTER SHUTDOWN. THE ENGINE CAN STAY HOT FOR A LONG TIME. IF YOU DO NOT OBEY THIS INSTRUCTION, INJURY CAN OCCUR.

ZONE: 210
ZONE: 410
ZONE: 420
ZONE: 430
ZONE: 440

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE
No specific	AR	CAP - BLANKING
No specific	AR	SAFETY CLIP - CIRCUIT BREAKER
No specific	AR	WARNING NOTICE(S)

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
210	CKPT,FWD COMPT BHD TO FLT COMPT BULKHEAD
410	ENG 1 PYLON BOX AND FORWARD FAIRING
420	ENG 2 PYLON BOX AND FORWARD FAIRING
430	ENG 1 AIR INTAKE, FAN AND ACCESS GEARBOX
440	ENG 2 AIR INTAKE, FAN AND ACCESS GEARBOX
FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
437AL, 438AR
FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
447AL, 448AR

C. Referenced Information

REFERENCE	DESIGNATION
TASK 71-13-00-010-802-A	Opening of the Fan Cowl Doors
Maintenance-Interphone Jack Harness

3. Job Set-up
Subtask 23-44-41-941-054-A ** ON A/C NOT FOR ALL

A. Safety Precautions
(1) On the center pedestal, on ENG panel 115VU:
(a) Make sure that the ENG/MODE selector switch is in the NORM position.
(b) Make sure that the ENG/MASTER 1(2) control switch was in the OFF position not less than five minutes before you do this procedure.
(c) Put the WARNING NOTICE(S) in position to tell persons not to operate the ENG/MODE selector switch and the ENG/MASTER 1(2) control switch.
(2) On the ENG section of maintenance panel 50VU:
(a) Make sure that the ON legend of the FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put the WARNING NOTICE(S) in position to tell persons not to energize FADEC 1(2).

Subtask 23-44-41-865-069-A ** ON A/C NOT FOR ALL

B. Open, safety and tag this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
FOR FIN: 101RH (DIRCIDS, 1)
49VU	AIR COND/CIDS/SDF/DIR1 ESS	15WH	C05
49VU	COM/CIDS/DIR ESS/1	150RH	G01
121VU	COM NAV/CIDS/DIR NORM/1	151RH	M05
122VU	AIR COND/CIDS/SDF/DIR NORM/1	17WH	T17
FOR FIN: 102RH (DIRCIDS, 2)
49VU	AIR COND/CIDS/SDF/DIR2 ESS	18WH	C06
49VU	COM/CIDS/DIR ESS/2	157RH	G02
49VU	COM/CIDS/DIR ESS/1	150RH	G01
121VU	COM NAV/CIDS/DIR NORM/2	156RH	M06
121VU	COM NAV/CIDS/DIR NORM/1	151RH	M05
122VU	AIR COND/CIDS/SDF/DIR NORM/2	14WH	T18

Subtask 23-44-41-010-055-A ** ON A/C NOT FOR ALL

C. Get Access
(1) Open the fan cowl doors (Ref. AMM TASK 71-13-00-010-802):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
437AL, 438AR
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
447AL, 448AR.
(2) Put the ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE in position.

4. Procedure

CAUTION: WIPE CLEAN ALL PARTS AND TOOLS AS NECESSARY TO REMOVE UNWANTED DEBRIS AND PREVENT DAMAGE TO THE ENGINE.

Subtask 23-44-41-020-059-A ** ON A/C NOT FOR ALL

A. Removal of the Maintenance-Interphone Jack Harness

Maintenance-Interphone Jack Harness ** ON A/C NOT FOR ALL

(1) Remove the four screws (7).
(2) Remove the mounting plate (6) and the maintenance-interphone jack harness (1) (4000RJ) from the interphone bracket.
(3) Disconnect the pylon harness from the maintenance-interphone jack harness (1) (4107VC).
(4) Put the CAP - BLANKING on the pylon harness.
(5) Remove the four screws (3) and four washers (2) that attach the maintenance-interphone jack harness (1) (4107VC) to the interphone disconnect panel.
(6) For configuration 1:
(a) Remove the maintenance-interphone jack harness (1) from the door as follows:
1 Remove the 12 screws (5) that attach the 12 clamps (4) and the maintenance-interphone jack harness (1) to the brackets on the right fan cowl-door.
2 Remove the 12 clamps (4) and the maintenance-interphone jack harness (1) from the right fan cowl-door.
3 Remove the 12 clamps (4) and the mounting plate (6) from the maintenance-interphone jack harness (1).
(7) For configuration 2:
(a) Remove the maintenance-interphone jack harness (1) from the door as follows:
1 Remove the 12 nuts (10) and the 12 washers (9) that attach the 11 clamps (11), the clamp (8) and the maintenance-interphone jack harness (1) to the studs on the right fan cowl-door.
2 Remove the clamp (8), the 11 clamps (11) and the maintenance-interphone jack harness (1) from the right fan cowl-door.
3 Remove the clamp (8), the 11 clamps (11) and the mounting plate (6) from the maintenance-interphone jack harness (1).
(8) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.

[Rev.10 from 2021] 2026.03.31 23:15:13 UTC