DOC AIRBUS | AMM A320FRemoval of the Video Tape Reproducer (VTR)
TASK 23-36-52-000-001-A
Removal of the Video Tape Reproducer (VTR)
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Work Zones and Access Panels
C. Referenced Information
3. Job Set-up
Subtask 23-36-52-865-068-A ** ON A/C NOT FOR ALL
Subtask 23-36-52-020-050-M ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.02 06:12:11 UTC
Removal of the Video Tape Reproducer (VTR)
WARNING:
ISOLATE THE ELECTRICAL CIRCUITS FROM THE RELATED EQUIPMENT AND THE ENVIRONMENT.
1. Reason for the JobSelf explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | AR | CAP - BLANKING |
| No specific | AR | SAFETY CLIP - CIRCUIT BREAKER |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 220 | FWD CAB UTILITY AREAS |
| 230 | FWD PASSENGER COMPARTMENT |
| REFERENCE | DESIGNATION |
|---|---|
Video Tape ReproducerSubtask 23-36-52-865-068-A ** ON A/C NOT FOR ALL
A. Open, safety and tag this(these) circuit breaker(s):
Subtask 23-36-52-010-050-B ** ON A/C NOT FOR ALL | PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 2000VU | PES-VIDEO-CABIN-RH AFT | 25MH | C06 |
| 2000VU | PES-VIDEO-CABIN-LH | 23MH | C05 |
| 2000VU | PES-VIDEO-CABIN-RH FWD | 24MH | C04 |
| 2000VU | PES-VIDEO-CABIN-LH FWD | 22MH | C03 |
| 2000VU | PES-VIDEO-CONTROL-VCC | 21MH | C02 |
| 2000VU | PES-VIDEO-CONTROL-MAIN | 20MH | C01 |
B. Get Access
(1) Open the access doors of the left forward overhead stowage compartment between FR20 and FR23.
(2) Open the front door of the left overhead stowage compartment.
4. Procedure(1) Open the access doors of the left forward overhead stowage compartment between FR20 and FR23.
(2) Open the front door of the left overhead stowage compartment.
Subtask 23-36-52-020-050-M ** ON A/C NOT FOR ALL
A. Removal of the Video Tape Reproducers (VTR) 12MH and 13MH
(1) Removal of the VTR 12MH
(a) Remove the cover (2) to get access to special rack (8).
(b) Loosen the knurled nuts (5) and lower them from the lugs (6).
(c) Carefully push the VTR (3) until the lugs (4) come free from the brackets (1).
(d) Pull and remove the VTR (3) from the special rack (8).
(e) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
(2) Removal of the VTR 13MH
(a) Loosen the knurled nuts (12) and lower them from the lugs (11).
(b) Pull and remove the VTR 13MH (10) from the rack (14).
(c) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
(1) Removal of the VTR 12MH
(a) Remove the cover (2) to get access to special rack (8).
(b) Loosen the knurled nuts (5) and lower them from the lugs (6).
(c) Carefully push the VTR (3) until the lugs (4) come free from the brackets (1).
(d) Pull and remove the VTR (3) from the special rack (8).
(e) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
(2) Removal of the VTR 13MH
(a) Loosen the knurled nuts (12) and lower them from the lugs (11).
(b) Pull and remove the VTR 13MH (10) from the rack (14).
(c) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.