W DOC AIRBUS | AMM A320F

Configuration of the Main Multiplexer with a Laptop

TASK 23-33-00-600-014-A
Configuration of the Main Multiplexer with a Laptop

FIN: 8MK ** ON A/C NOT FOR ALL
1. Reason for the Job
Self explanatory
2. Job Set-up Information
 A. Fixtures, Tools, Test and Support Equipment
REFERENCE
QTY
DESIGNATION
No specific
1
ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE
No specific
AR
LAPTOP - INTERFACE SOFTWARE RS232
No specific
AR
SAFETY CLIP - CIRCUIT BREAKER
 B. Work Zones and Access Panels
ZONE/ACCESS
ZONE DESCRIPTION
824
 C. Referenced Information
REFERENCE
DESIGNATION
TASK 23-33-00-820-001-A
Adjustment of the DIP - Switch Positions of the Main Multiplexer
TASK 24-41-00-861-002-A
Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01
Energize the Aircraft Electrical Circuits from the APU
TASK 24-41-00-861-002-A-02
Energize the Aircraft Electrical Circuits from Engine 1(2)
TASK 24-41-00-862-002-A
De-energize the Aircraft Electrical Circuits Supplied from the External Power
TASK 24-41-00-862-002-A-01
De-energize the Aircraft Electrical Circuits Supplied from the APU
TASK 24-41-00-862-002-A-02
De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2)
TASK 52-41-00-010-002-A
Open the Avionics Compartment Doors for Access
TASK 52-41-00-410-002-A
Close the Avionics Compartment Doors after Access
3. Job Set-up
Subtask 23-33-00-010-058-A ** ON A/C NOT FOR ALL
A. Get Access
   (1) Put the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE in position below the access door 824.
   (2) Open the access door 824 (Ref. AMM TASK 52-41-00-010-002).
Subtask 23-33-00-860-075-A ** ON A/C NOT FOR ALL
B. Aircraft Maintenance Configuration
   (1) Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002).
   (2) Make sure that the DIP-switches of the Main Multiplexer (MM) 8MK are set as listed in the table below. Adjust them if necessary (Ref. AMM TASK 23-33-00-820-001).
SWITCH
1
2
3
4
5
6
7
8
DSW 1
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
DSW 2
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
DSW 3
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
DSW 4
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
DSW 5
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
NOTE: The location of the DIP DSW1 is near to the top of the MM 8MK. The location of the DIP DSW5 is near to the bottom of the MM 8MK.
The location of switch 8 of each DIP is near to the front of the MM 8MK.
NOTE: The switches 7 and 8 of the DIP DSW5 control the electronic programming of the MM 8MK.
Subtask 23-33-00-865-137-A ** ON A/C NOT FOR ALL
C. Open, safety and tag this(these) circuit breaker(s):
PANELDESIGNATIONFINLOCATION
** ON A/C NOT FOR ALL
2000VUPES MUSIC FWD - RH24MKD03
2000VUPES-MUSIC-CABIN-LH23MKD02
2000VUPES MUSIC CTL21MKD01
Subtask 23-33-00-480-066-A ** ON A/C NOT FOR ALL
D. Install the Support Equipment
   (1) Connect the LAPTOP - INTERFACE SOFTWARE RS232 with the cable to the RS 232 port of the MM 8MK.
   (2) Energize the laptop and make sure, that the software DBMT tool is installed.
NOTE: The software starts automatically.
You will find more information in the instruction manual P/N IM-AM9027-01.
Subtask 23-33-00-865-138-A ** ON A/C NOT FOR ALL
E. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
PANELDESIGNATIONFINLOCATION
** ON A/C NOT FOR ALL
2000VUPES MUSIC FWD - RH24MKD03
2000VUPES-MUSIC-CABIN-LH23MKD02
2000VUPES MUSIC CTL21MKD01
4. Procedure
Subtask 23-33-00-970-066-I ** ON A/C NOT FOR ALL
A. Configuration of the Main Multiplexer 8MK with the Laptop.
   (1) Click the 'New MPES' tab on the DBMT screen.
   (2) Click the 'PORT' arrow down button to show the 'PORT' selection list.
   (3) Click 'COM 1' to make a selection of the connected RS 232 port.
   (4) Click the 'Connect' button.
   (5) Click the 'RECEIVE' button.
NOTE: The laptop will now download the configuration from the MM 8MK and will then show it on the 'New MPES' screen.
   (6) To change the configuration of the MM 8MK that is shown, do the steps that follow.
     (a) On the 'System CH Setting' area, make these selections:
1 1/2(ST)
2 3/4(ST)
3 5/6(ST)
4 7/8(ST)
5 9(MON)
6 10(MON)
7 11/12(ST)
8 Skip
9 Skip
10 Skip
11 Skip
12 Skip
13 Skip
14 Skip
15 Skip
16 Skip
17 Skip
18 Skip
     (b) On the 'PCU Video CH Setting'/'Bilingual Tag' area, make this selections:
1 Bilingual
2 Bilingual
3 Bilingual
     (c) On the 'PCU Video CH Setting'/'Video Zone' area, make this selections:
1-1 17
1-2 18
2-1 17
2-2 18
3-1 NONE
3-2 NONE
     (d) On the 'Mode Setting' area, make this selection:
NORMAL
     (e) On the 'Vol Default Position' area, make this selection:
0
     (f) On the 'PCU Default CH' area, make this selection:
1
   (7) Click the 'SEND' button.
NOTE: The laptop will now download the new configuration to the MM 8MK.
   (8) Click the 'Disconnect' button.
5. Close-up
Subtask 23-33-00-865-139-A ** ON A/C NOT FOR ALL
A. Open, safety and tag this(these) circuit breaker(s):
PANELDESIGNATIONFINLOCATION
** ON A/C NOT FOR ALL
2000VUPES MUSIC FWD - RH24MKD03
2000VUPES-MUSIC-CABIN-LH23MKD02
2000VUPES MUSIC CTL21MKD01
Subtask 23-33-00-080-066-A ** ON A/C NOT FOR ALL
B. Remove the Support Equipment
   (1) De-energize the laptop.
   (2) Disconnect the LAPTOP - INTERFACE SOFTWARE RS232 and the cable from the RS 232 port of the MM 8MK.
Subtask 23-33-00-865-140-A ** ON A/C NOT FOR ALL
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
PANELDESIGNATIONFINLOCATION
** ON A/C NOT FOR ALL
2000VUPES MUSIC FWD - RH24MKD03
2000VUPES-MUSIC-CABIN-LH23MKD02
2000VUPES MUSIC CTL21MKD01
Subtask 23-33-00-740-055-B ** ON A/C NOT FOR ALL
D. Do the BITE-test of the PES (music) with the Flight Attendant Panel (Ref. AMM D/O 23-33-00-74).
Subtask 23-33-00-860-076-A ** ON A/C NOT FOR ALL
E. De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002).
Subtask 23-33-00-410-059-A ** ON A/C NOT FOR ALL
F. Close Access
   (1) Close the access door 824 (Ref. AMM TASK 52-41-00-410-002).
   (2) Remove the access platform(s).
[Rev.9 from 2019] 2026.04.02 06:12:05 UTC
"WTRUIB" 2025