DOC AIRBUS | AMM A320FRemoval of the Sensor Duct
TASK 21-58-61-000-803-A
Removal of the Sensor Duct
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Work Zones and Access Panels
C. Referenced Information
3. Job Set-up
Subtask 21-58-61-861-053-A ** ON A/C NOT FOR ALL Subtask 21-58-61-865-064-A ** ON A/C NOT FOR ALL
Subtask 21-58-61-020-053-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.02 06:11:36 UTC
Removal of the Sensor Duct
WARNING:
MAKE SURE THAT AIR IS NOT SUPPLIED TO THE AIR CONDITIONING SYSTEM FROM THE MAIN ENGINE, THE APU OR A GROUND SOURCE.
HOT COMPRESSED AIR CAN CAUSE INJURY TO PERSONNEL.
WARNING:
DO NOT TOUCH THE COMPONENT UNTIL IT IS SUFFICIENTLY
COOL TO PREVENT BURNS.
CAUTION:
BE VERY CAREFUL WHEN YOU DO WORK ON OR NEAR THE AIR-CONDITIONING DUCTS. THE DUCTS ARE MADE OF THIN MATERIAL AND YOU CAN EASILY BREAK THEM.
ZONE: 191
1. Reason for the JobSelf explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | 1 | ACCESS PLATFORM 2M (6 FT) |
| No specific | AR | PLUG - BLANKING |
| No specific | AR | SAFETY CLIP - CIRCUIT BREAKER |
| No specific | AR | WARNING NOTICE(S) |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 191 | AIR CONDITIONING COMPT AND FAIRINGS |
| 191CB, 191DB, 191KB, 192KB |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 21-58-11-000-001-A | Removal of the Duct Temperature Sensor |
| TASK 21-58-12-000-001-A | Removal of the Pressure Sensor |
| TASK 24-41-00-861-002-A | Energize the Aircraft Electrical Circuits from the External Power |
| TASK 24-41-00-861-002-A-01 | Energize the Aircraft Electrical Circuits from the APU |
| TASK 24-41-00-861-002-A-02 | Energize the Aircraft Electrical Circuits from Engine 1(2) |
| TASK 53-35-13-000-002-A | Removal of the Quick-Release Access Panels from the Belly Fairing Structure |
Sensor DuctSubtask 21-58-61-861-053-A ** ON A/C NOT FOR ALL Subtask 21-58-61-865-064-A ** ON A/C NOT FOR ALL
B. Open, safety and tag this(these) circuit breaker(s):
Subtask 21-58-61-865-058-A | PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 49VU | AIR BLEED/X FEED/VALVE/BAT | 2HV | D13 |
| 49VU | AIR COND/TEMP CTL/SYS 1 CHAN B/28VDC | 52HH | D08 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | AIR BLEED/ENG 1/CTL | 3HA1 | D12 |
| 49VU | AIR BLEED/ENG 1/MONG | 2HA1 | D11 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | AIR BLEED/ENG 2/MONG | 3HA2 | D12 |
| 49VU | AIR BLEED/ENG 1/CTL | 2HA1 | D11 |
| ** ON A/C NOT FOR ALL | |||
| 121VU | IGGS/CTRL | 7YA | N28 |
| ** ON A/C NOT FOR ALL | |||
| 121VU | IGGS/CTRL | 7YA | P28 |
| ** ON A/C NOT FOR ALL | |||
| 122VU | CSAS / CTRL | 1HW | U17 |
| 122VU | AIR COND/TEMP CTL SYS 1/CHAN A/115VAC | 49HH | X22 |
| 122VU | AIR COND/TEMP CTL SYS 1/CHAN A/28VDC | 51HH | X21 |
| 122VU | AIR COND/TEMP CTL SYS 1/CHAN B/115VAC | 50HH | Y18 |
| 122VU | AIR BLEED/X FEED VALVE/NORM | 1HV | Z20 |
| ** ON A/C NOT FOR ALL | |||
| 122VU | AIR BLEED/ENG 2/CTL | 3HA2 | Z23 |
| 122VU | AIR BLEED/ENG 2/MONG | 2HA2 | Z22 |
| ** ON A/C NOT FOR ALL | |||
| 122VU | AIR BLEED/ENG 1/MONG | 3HA1 | Z23 |
| 122VU | AIR BLEED/ENG 2/CTL | 2HA2 | Z22 |
DELETED
Subtask 21-58-61-941-053-A ** ON A/C NOT FOR ALL D. Safety Precautions
(1) In the cockpit, on AIR COND panel 30VU:
(a) Make sure that the APU BLEED pushbutton switch is released (the OFF legend is on).
(b) Make sure that the ENG 1 BLEED and the ENG 2 BLEED pushbutton switches are released (the OFF legends are on).
(c) Make sure that the PACK 1 and the PACK 2 pushbutton switches are released (the OFF legends are on).
(d) Make sure that the HOT AIR pushbutton switch is released (the OFF legend is on).
(e) Put the WARNING NOTICE(S) in position to tell persons not to operate these pushbutton switches.
(2) At access doors 191CB and 191DB:
(a) On the LP and the HP ground connectors, put the WARNING NOTICE(S) in position to tell persons not to supply the ground air.
Subtask 21-58-61-010-054-A ** ON A/C NOT FOR ALL (1) In the cockpit, on AIR COND panel 30VU:
(a) Make sure that the APU BLEED pushbutton switch is released (the OFF legend is on).
(b) Make sure that the ENG 1 BLEED and the ENG 2 BLEED pushbutton switches are released (the OFF legends are on).
(c) Make sure that the PACK 1 and the PACK 2 pushbutton switches are released (the OFF legends are on).
(d) Make sure that the HOT AIR pushbutton switch is released (the OFF legend is on).
(e) Put the WARNING NOTICE(S) in position to tell persons not to operate these pushbutton switches.
(2) At access doors 191CB and 191DB:
(a) On the LP and the HP ground connectors, put the WARNING NOTICE(S) in position to tell persons not to supply the ground air.
E. Get Access
(1) Put the ACCESS PLATFORM 2M (6 FT) in position at zone 191.
(2) Remove applicable access panel(s) 191KB and/or 192KB (Ref. AMM TASK 53-35-13-000-002).
4. Procedure(1) Put the ACCESS PLATFORM 2M (6 FT) in position at zone 191.
(2) Remove applicable access panel(s) 191KB and/or 192KB (Ref. AMM TASK 53-35-13-000-002).
Subtask 21-58-61-020-053-A ** ON A/C NOT FOR ALL
A. Removal of the Sensor Duct
(1) Remove the duct temperature sensor (13) (Ref. AMM TASK 21-58-11-000-001).
(2) Remove the pressure sensor (14) (Ref. AMM TASK 21-58-12-000-001).
(3) Remove the nuts (9), washers (3), screws (2) and bonding strap (5).
(4) Remove the nuts (11), the washers (12) and the screws (19).
(5) Hold the duct (10) and remove the nuts (18), the washers (16) and the screws (15).
(6) Remove the duct (10) from the temperature control module (1) and discard the packing (17).
(7) Remove the seal (6) and discard it.
(8) Remove the seal (7) and discard it.
(9) Put the PLUG-BLANKING in each disconnected line end.
(1) Remove the duct temperature sensor (13) (Ref. AMM TASK 21-58-11-000-001).
(2) Remove the pressure sensor (14) (Ref. AMM TASK 21-58-12-000-001).
(3) Remove the nuts (9), washers (3), screws (2) and bonding strap (5).
(4) Remove the nuts (11), the washers (12) and the screws (19).
(5) Hold the duct (10) and remove the nuts (18), the washers (16) and the screws (15).
(6) Remove the duct (10) from the temperature control module (1) and discard the packing (17).
(7) Remove the seal (6) and discard it.
(8) Remove the seal (7) and discard it.
(9) Put the PLUG-BLANKING in each disconnected line end.