Attachment Components (In-Service Wear Limits) - Ozone Filter

TASK 21-51-41-200-001-A
Attachment Components (In-Service Wear Limits) - Ozone Filter

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Referenced Information

REFERENCE	DESIGNATION
TASK 21-51-00-300-001-A	Attachment Components - Repair/Replacement
Ozone Filter - Attachment Components

3. Job Set-up
Subtask 21-51-41-010-053-A

A. Get Access
(1) Make sure that the applicable components are disassembled to do the inspection procedure.

4. Procedure
Subtask 21-51-41-210-051-A

A. Visual Inspection of the Spherical Bearings in the Support-Rod and Bracket Assembly
(1) On the support-rod (1):
(a) Use an applicable measurement method and do a check for radial and axial play at the spherical bearings (2).
(b) If you find more than 0.05 mm (0.0020 in.) radial play or more than 0.2 mm (0.0079 in.) axial play in a spherical bearing (2) then you must replace the applicable rod eye-end (Ref. AMM TASK 21-51-00-300-001).
(2) On the bracket assembly (12):
(a) Use an applicable measurement method and do a check for radial and axial play at the spherical bearings (2).
(b) If you find more than 0.05 mm (0.0020 in.) radial play or more than 0.2 mm (0.0079 in.) axial play in a spherical bearing (2) then you must replace the bracket assembly (12).

Subtask 21-51-41-220-051-A

B. In-Service Wear Limits
(1) Use an applicable measurement equipment and measure the outer diameter of the bushings (6) and the inner diameter of the shouldered bushings (4).

If the values of the components are 'out of limits' then you must replace them:
For shouldered bushings (4) (Ref. AMM TASK 21-51-00-300-001).

Figure Detail and the Related Item Number	In-Service Wear Limits
For outer diameter of the bushings (6), refer to View B - B	8.979 (0.3535)	8.995 (0.3541)
			0.0050 (0.0002)	0.0430 (0.0017)
For inner diameter of the shouldered bushings (4), refer to View B - B	9.000 (0.3543)	9.022 (0.3552)

Subtask 21-51-41-220-052-A

C. In-Service Wear Limits
(1) Use an applicable measurement equipment and measure the outer diameter of the bolts (5) and the inner diameter of the bushings (6).

If the values of the components are 'out of limits' then you must replace them.

Figure Detail and the Related Item Number	In-Service Wear Limits
For outer diameter of the bolts (5), refer to View B - B	6.318 (0.2487)	6.335 (0.2494)
			0.0150 (0.0006)	0.0470 (0.0018)
For inner diameter of the bushings (6), refer to View B - B	6.350 (0.2500)	6.365 (0.2506)

Subtask 21-51-41-220-053-A

D. In-Service Wear Limits
(1) Use an applicable measurement equipment and measure the outer diameter of the bolts (5) and the inner diameter of the shouldered bushings (3).

If the values of the components are 'out of limits' then you must replace them:
For shouldered bushings (3) (Ref. AMM TASK 21-51-00-300-001).

Figure Detail and the Related Item Number	In-Service Wear Limits
For outer diameter of the bolts (5), refer to View B - B	6.318 (0.2487)	6.335 (0.2494)
			0.0150 (0.0006)	0.0470 (0.0018)
For inner diameter of the shouldered bushings (3), refer to View B - B	6.350 (0.2500)	6.365 (0.2506)

[Rev.10 from 2021] 2026.04.02 06:11:23 UTC