DOC AIRBUS | AMM A320FDisinfection with Self-Sanitizing Aircraft-Interior Polish (Airdal) on Hard Surfaces in the Passenger Cabin
TASK 12-21-12-670-803-A
Disinfection with Self-Sanitizing Aircraft-Interior Polish (Airdal) on Hard Surfaces in the Passenger Cabin
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Consumable Materials
C. Work Zones and Access Panels
D. Referenced Information
3. Job Set-up
Subtask 12-21-12-861-065-A Subtask 12-21-12-860-054-A
Subtask 12-21-12-670-052-A
Subtask 12-21-12-410-059-A
[Rev.10 from 2021]
2026.04.02 06:10:24 UTC
Disinfection with Self-Sanitizing Aircraft-Interior Polish (Airdal) on Hard Surfaces in the Passenger Cabin
WARNING:
BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
CAUTION:
ALWAYS USE A NEW CLEAN CLOTH TO POLISH THE SURFACES. IF YOU DO NOT OBEY THIS PRECAUTION, THE DISINFECTION OF THE SURFACES WILL NOT BE SUFFICIENT.
CAUTION:
MAKE SURE THAT THERE IS NO ABRASIVE MATERIAL ON THE SURFACE. ABRASIVE MATERIALS CAN CAUSE DAMAGE TO THE SURFACE.
CAUTION:
DO NOT APPLY AIRDAL ON SCREENS AND TOUCHSCREENS. THIS CAN CAUSE DAMAGE TO THE EQUIPMENT.
NOTE: There are alternative procedures to disinfect surfaces in the passenger cabin. For the other procedures, refer to the related task in this page block.
NOTE: You can apply Airdal to these areas and equipment in the cabin: tables, armrests, keyboards, handles, overhead storage compartments, panels and linings, lavatories, galleys, social areas and self-service bars.
ZONE: 200
1. Reason for the JobSelf explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | AR | GLOVES-EN374 TYPE B |
| No specific | AR | MASK FFP3 TYPE |
| No specific | AR | SAFETY GOGGLES EN166 TYPE |
| No specific | AR | THERMOMETER |
| REFERENCE | DESIGNATION |
|---|---|
| (Material No.11LAD1) | Self-Sanitizing-Aircraft interior Polish - |
| (Material No.14SBA1) | Textile-Lint free Cotton - |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 200 | UPPER HALF FUSELAGE |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 24-42-00-861-001-A | Energize the Ground Service Network from the External Power |
| TASK 24-42-00-862-001-A | De-energize the Ground Service Network Supplied from the External Power |
Subtask 12-21-12-861-065-A Subtask 12-21-12-860-054-A
B. Preparation for the Aircraft-Interior Polish Application
(1) Measure and record the cabin ambient temperature with a THERMOMETER.
(2) Make sure that the cabin ambient temperature is 23°C (73,4°F) or more.
(3) If the cabin ambient temperature is less than 23°C (73,4 °F):
(a) Increase the temperature in the cabin area to 23°C (73,4°F) or more with an external heat-distribution system.
4. Procedure(1) Measure and record the cabin ambient temperature with a THERMOMETER.
(2) Make sure that the cabin ambient temperature is 23°C (73,4°F) or more.
(3) If the cabin ambient temperature is less than 23°C (73,4 °F):
(a) Increase the temperature in the cabin area to 23°C (73,4°F) or more with an external heat-distribution system.
NOTE: It is the responsibility of the operator to get the correct external heat-distribution system for this task.
(4) Make sure that the cabin ambient temperature stays at 23°C (73,4°F) or more.Subtask 12-21-12-670-052-A
A. Disinfection with Self-Sanitizing Aircraft-Interior Polish (Airdal) on Hard Surfaces (Non-Absorbing) in the Passenger Cabin
(a) Put on GLOVES-EN374 TYPE B.
(b) Apply a layer of AIRDAL Cleaner and Primer Self-Sanitizing-Aircraft interior Polish - (Material No.11LAD1) to the surfaces. Make sure that you apply the layer fully to the surfaces.
(c) Immediately polish the surfaces with a clean Textile-Lint free Cotton - (Material No.14SBA1) until they are fully dry and there are no smears.
(d) Apply a layer of AIRDAL Coating Self-Sanitizing-Aircraft interior Polish - (Material No.11LAD1) to the surfaces. Make sure that you apply the layer fully to the surfaces.
(f) Let the disinfected surfaces dry for 6 hours at a cabin ambient temperature of minimum 23°C (73,4°F).
(2) If you spray the disinfectant:
(a) Put on GLOVES-EN374 TYPE B. For overhead spraying work, use SAFETY GOGGLES EN166 TYPE and a MASK FFP3 TYPE.
(b) Apply a layer of AIRDAL Cleaner and Primer Self-Sanitizing-Aircraft interior Polish - (Material No.11LAD1) to the surfaces with the hand sprayer. Make sure that you apply the layer fully to the surfaces.
(c) Immediately polish the surfaces with a clean Textile-Lint free Cotton - (Material No.14SBA1) until they are fully dry and there are no smears.
(d) Apply a layer of AIRDAL Coating Self-Sanitizing-Aircraft interior Polish - (Material No.11LAD1) to the surfaces with the hand sprayer. Make sure that you apply the layer fully to the surfaces.
(f) Let the disinfected surfaces dry for 6 hours at a cabin ambient temperature of minimum 23°C (73,4°F).
5. Close-upNOTE: With AIRDAL Cleaner and Primer you clean and prepare the surfaces at the same time. Thus it is not necessary to clean the surfaces before you apply a layer of AIRDAL Cleaner and Primer.
(1) If you use wet wipes:(a) Put on GLOVES-EN374 TYPE B.
(b) Apply a layer of AIRDAL Cleaner and Primer Self-Sanitizing-Aircraft interior Polish - (Material No.11LAD1) to the surfaces. Make sure that you apply the layer fully to the surfaces.
(c) Immediately polish the surfaces with a clean Textile-Lint free Cotton - (Material No.14SBA1) until they are fully dry and there are no smears.
(d) Apply a layer of AIRDAL Coating Self-Sanitizing-Aircraft interior Polish - (Material No.11LAD1) to the surfaces. Make sure that you apply the layer fully to the surfaces.
CAUTION:
ALWAYS USE A NEW CLEAN CLOTH TO POLISH THE SURFACES. IF YOU DO NOT OBEY THIS PRECAUTION, THE DISINFECTION OF THE SURFACES WILL NOT BE SUFFICIENT.
(e) Immediately polish the surfaces again with a clean Textile-Lint free Cotton - (Material No.14SBA1) until they are fully dry and there are no smears.(f) Let the disinfected surfaces dry for 6 hours at a cabin ambient temperature of minimum 23°C (73,4°F).
(2) If you spray the disinfectant:
(a) Put on GLOVES-EN374 TYPE B. For overhead spraying work, use SAFETY GOGGLES EN166 TYPE and a MASK FFP3 TYPE.
(b) Apply a layer of AIRDAL Cleaner and Primer Self-Sanitizing-Aircraft interior Polish - (Material No.11LAD1) to the surfaces with the hand sprayer. Make sure that you apply the layer fully to the surfaces.
(c) Immediately polish the surfaces with a clean Textile-Lint free Cotton - (Material No.14SBA1) until they are fully dry and there are no smears.
(d) Apply a layer of AIRDAL Coating Self-Sanitizing-Aircraft interior Polish - (Material No.11LAD1) to the surfaces with the hand sprayer. Make sure that you apply the layer fully to the surfaces.
CAUTION:
ALWAYS USE A NEW CLEAN CLOTH TO POLISH THE SURFACES. IF YOU DO NOT OBEY THIS PRECAUTION, THE DISINFECTION OF THE SURFACES WILL NOT BE SUFFICIENT.
(e) Immediately polish the surfaces again with a clean Textile-Lint free Cotton - (Material No.14SBA1) until they are fully dry and there are no smears.(f) Let the disinfected surfaces dry for 6 hours at a cabin ambient temperature of minimum 23°C (73,4°F).
Subtask 12-21-12-410-059-A
A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) If you used an external heat-distribution system, stop and disconnect it.
Subtask 12-21-12-862-066-A (1) Make sure that the work area is clean and clear of tools and other items.
(2) If you used an external heat-distribution system, stop and disconnect it.